Design Without Compromise.
high-quality tattoo products.
tools built for simplicity, ease, and excellence in Tattooing.
The Blackbird power supply. Pulse (can control coil’s speed, hit, duty cycle all independently) and standard mode. 5 amp output. Continuous on mode. 5 memory functions for each mode. Comes with magnetic bracket for mounting to metal workstation.
Betty V2 in a glossy polished finish.
The long A-bar mitigates the common spitting issues we’ve all encountered with other machines, and allows for a wider stroke and operating range. Fine lines, sure. Fat sharpie one-pass lines? You bet. Gentle layering, to all out whips. Betty has you covered.
Weight: 5.1oz
Stroke: 2mm-5.5+
Voltage range: 2.8ish-7.5+
Use a wide rubber band with just enough tension to stabilize the needle bar. Anything more is excessive and will make it hit softer, and not as punchy at lower volts.
Positive up on the clip cord is snappier, positive down is a bit more mellow. I usually always run positive up.
This machine will push ANYTHING. Full stop.
The armature bar on this machine is absolutely massive, which does a couple things: Increases the stroke range and imparts a more linear motion at the tip of the bar. In turn, reducing spitting. That being said, when a machine hits really hard and is moving really fast, spitting can still occur. The stroke range is 1mm-5mm+. It’s an amazing liner, but also really shines as a packer/shader/dot whipper in the low end with the stroke maxed out. The stroke adjustment thumbscrew on the back clicks into position while turning, so there’s no need for a tool to lock it into place. Another thing that sets this machine apart is the size. It feels like a machine should. Think the size of a standard coil machine. It also sits really low on the tube, adding to the ergonomics.
Betty V2 in a blush pink.
The long A-bar mitigates the common spitting issues we’ve all encountered with other machines, and allows for a wider stroke and operating range. Fine lines, sure. Fat sharpie one-pass lines? You bet. Gentle layering, to all out whips. Betty has you covered.
Weight: 5.1oz
Stroke: 2mm-5.5+
Voltage range: 2.8ish-7.5+
Use a wide rubber band with just enough tension to stabilize the needle bar. Anything more is excessive and will make it hit softer, and not as punchy at lower volts.
Positive up on the clip cord is snappier, positive down is a bit more mellow. I usually always run positive up.
Betty V2 in a sexy desert brown, with polished brass bits.
The long A-bar mitigates the common spitting issues we’ve all encountered with other machines, and allows for a wider stroke and operating range. Fine lines, sure. Fat sharpie one-pass lines? You bet. Gentle layering, to all out whips. Betty has you covered.
Weight: 5.1oz
Stroke: 2mm-5.5+
Voltage range: 2.8ish-7.5+
Use a wide rubber band with just enough tension to stabilize the needle bar. Anything more is excessive and will make it hit softer, and not as punchy at lower volts.
Positive up on the clip cord is snappier, positive down is a bit more mellow. I usually always run positive up.
Betty V2 in a terra cotta with polished brass bits. One of my favorites.
The long A-bar mitigates the common spitting issues we’ve all encountered with other machines, and allows for a wider stroke and operating range. Fine lines, sure. Fat sharpie one-pass lines? You bet. Gentle layering, to all out whips. Betty has you covered.
Weight: 5.1oz
Stroke: 2mm-5.5+
Voltage range: 2.8ish-7.5+
Use a wide rubber band with just enough tension to stabilize the needle bar. Anything more is excessive and will make it hit softer, and not as punchy at lower volts.
Positive up on the clip cord is snappier, positive down is a bit more mellow. I usually always run positive up.